-- Network Working Group B. Ray
-- Request for Comments: 3276 PESA Switching Systems
-- Category: Standards Track R. Abbi
-- Alcatel
-- May 2002-- Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation
-- (HDSL2) and Single-Pair High-Speed Digital Subscriber
-- Line (SHDSL) LinesHDSL2-SHDSL-LINE-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Counter32,Unsigned32,Gauge32,NOTIFICATION-TYPE,Integer32,transmission FROM SNMPv2-SMI
RowStatus,TEXTUAL-CONVENTIONFROM SNMPv2-TC
ifIndex FROM IF-MIB
PerfCurrentCount,PerfIntervalCountFROM PerfHist-TC-MIB
SnmpAdminStringFROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUPFROM SNMPv2-CONF;hdsl2ShdslMIB MODULE-IDENTITYLAST-UPDATED"200205090000Z"-- May 9, 2002ORGANIZATION"ADSLMIB Working Group"
CONTACT-INFO"WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Postal: P.O. Box 37324
Raleigh NC 27627-7324
Email: sneedmike@hotmail.com
Co-editor: Bob Ray
PESA Switching Systems, Inc.
Postal: 330-A Wynn Drive
Huntsville, AL 35805 USA
Email: rray@pesa.com
Phone: +1 256 726 9200 ext. 142
Co-editor: Rajesh Abbi
Alcatel USA
Postal: 2912 Wake Forest Road
Raleigh, NC 27609-7860 USA
Email: Rajesh.Abbi@alcatel.com
Phone: +1 919 850 6194
"DESCRIPTION"This MIB module defines a collection of objects for managing
HDSL2/SHDSL lines. An agent may reside at either end of the
line, however the MIB is designed to require no management
communication between the modems beyond that inherent in the
low-level EOC line protocol as defined in ANSI T1E1.4/2000-006
(for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)."REVISION"200205090000Z"-- May 9, 2002DESCRIPTION"Initial version, published as RFC 3276."::={ transmission 48}hdsl2ShdslMibObjects OBJECTIDENTIFIER::={ hdsl2ShdslMIB 1}-- Textual Conventions used in this MIB
--Hdsl2ShdslPerfCurrDayCount::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval.
The value of this gauge starts at zero at the beginning of an
interval and is increased when associated events occur, until
the end of the 1-day interval. At that time the value of the
gauge is stored in the previous 1-day history interval, as
defined in a companion object of type
Hdsl2Shdsl1DayIntevalCount, and the current interval gauge
is restarted at zero.
In the case where the agent has no valid data available for
this interval the corresponding object instance is not
available and upon a retrieval request a corresponding error
message shall be returned to indicate that this instance does
not exist. Please note that zero is a valid value."SYNTAXGauge32Hdsl2Shdsl1DayIntervalCount::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"A counter associated with interface performance measurements
during the most previous 1-day (24 hour) measurement interval.
The value of this gauge is equal to the value of the current
day gauge, as defined in a companion object of type
Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
interval.
In the case where the agent has no valid data available for
this interval the corresponding object instance is not
available and upon a retrieval request a corresponding error
message shall be returned to indicate that this instance does
not exist."SYNTAXGauge32Hdsl2ShdslPerfTimeElapsed::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock or the addition
of a leap second, the current interval exceeds the maximum
value, the agent will return the maximum value.
For 15 minute intervals, the range is limited to (0..899).
For 24 hour intervals, the range is limited to (0..86399)."SYNTAXUnsigned32(0..86399)Hdsl2ShdslPerfIntervalThreshold::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the
alarm."SYNTAXUnsigned32(0..900)Hdsl2ShdslUnitId::=TEXTUAL-CONVENTION
STATUScurrentDESCRIPTION"This is the unique identification for all units in a
HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."SYNTAXINTEGER{xtuC(1),xtuR(2),xru1(3),xru2(4),xru3(5),xru4(6),xru5(7),xru6(8),xru7(9),xru8(10)}Hdsl2ShdslUnitSide::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This is the referenced side of a HDSL2/SHDSL unit - Network
or Customer side. The side facing the Network is the Network
side, while the side facing the Customer is the Customer side."
SYNTAXINTEGER{networkSide(1),customerSide(2)}Hdsl2ShdslWirePair::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This is the referenced pair of wires in a HDSL2/SHDSL Segment.
HDSL2 only supports a single pair (wirePair1), while SHDSL
supports an optional second pair (wirePair2)."SYNTAXINTEGER{wirePair1(1),wirePair2(2)}Hdsl2ShdslTransmissionModeType::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Contains the regional setting of the HDSL2/SHDSL span,
represented as a bit-map of possible settings. The various
bit positions are:
Bit Meaning Description
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B."SYNTAXBITS{region1(0),
region2(1)}Hdsl2ShdslClockReferenceType::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The various STU-C symbol clock references for the
HDSL2/SHDSL span, represented as an enumeration."SYNTAXINTEGER{localClk(1),-- Mode-1 per G991.2networkClk(2),-- Mode-2 per G991.2dataOrNetworkClk(3),-- Mode-3a per G991.2dataClk(4)-- Mode-3b per G991.2}-- Span Configuration Group
--hdsl2ShdslSpanConfTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslSpanConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports overall configuration of HDSL2/SHDSL
Spans. Entries in this table MUST be maintained in a
persistent manner."::={ hdsl2ShdslMibObjects 1}
hdsl2ShdslSpanConfEntry OBJECT-TYPESYNTAX Hdsl2ShdslSpanConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the hdsl2ShdslSpanConfTable. Each entry
represents the complete Span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."INDEX{ ifIndex }::={ hdsl2ShdslSpanConfTable 1}
Hdsl2ShdslSpanConfEntry ::=SEQUENCE{
hdsl2ShdslSpanConfNumRepeaters Unsigned32,
hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanConfAlarmProfile SnmpAdminString}hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPESYNTAXUnsigned32(0..8)UNITS"repeaters"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL Span."
::={ hdsl2ShdslSpanConfEntry 1}hdsl2ShdslSpanConfProfile OBJECT-TYPESYNTAXSnmpAdminString(SIZE(1..32))MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object is a pointer to a span configuration profile in
the hdsl2ShdslSpanConfProfileTable, which applies to this span.
The value of this object is the index of the referenced profile
in the hdsl2ShdslSpanConfProfileTable. Note that span
configuration profiles are only applicable to SHDSL lines.
HDSL2 lines MUST reference the default profile, 'DEFVAL'.
By default, this object will have the value 'DEFVAL' (the index
of the default profile).
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."::={ hdsl2ShdslSpanConfEntry 2}hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPESYNTAXSnmpAdminString(SIZE(1..32))MAX-ACCESSread-writeSTATUScurrentDESCRIPTION
"This object is a pointer to an Alarm configuration profile in
the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this
object is the index of the referenced profile in the
hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold
configuration in the referenced profile will be used by default
for all segment endpoints in this span. Individual endpoints
may override this profile by explicitly specifying some other
profile in the hdsl2ShdslEndpointConfTable. By default, this
object will have the value 'DEFVAL' (the index of the default
profile).
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."::={ hdsl2ShdslSpanConfEntry 3}-- Span Status Group
--hdsl2ShdslSpanStatusTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslSpanStatusEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides overall status information of
HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."::={ hdsl2ShdslMibObjects 2}hdsl2ShdslSpanStatusEntry OBJECT-TYPESYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."INDEX{ ifIndex }::={ hdsl2ShdslSpanStatusTable 1}
Hdsl2ShdslSpanStatusEntry ::=SEQUENCE{
hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
hdsl2ShdslStatusActualLineRate Unsigned32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType}hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPESYNTAXUnsigned32(0..8)MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."::={ hdsl2ShdslSpanStatusEntry 1}hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPESYNTAXUnsigned32(0..4112000)
UNITS"bps"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Contains the maximum attainable line rate in this HDSL2/SHDSL
span. This object provides the maximum rate the line is
capable of achieving. This is based upon measurements made
during line probing."::={ hdsl2ShdslSpanStatusEntry 2}hdsl2ShdslStatusActualLineRate OBJECT-TYPESYNTAXUnsigned32(0..4112000)UNITS"bps"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Contains the actual line rate in this HDSL2/SHDSL span. This
should equal ifSpeed."::={ hdsl2ShdslSpanStatusEntry 3}hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPESYNTAXHdsl2ShdslTransmissionModeTypeMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Contains the current Power Spectral Density (PSD) regional
setting of the HDSL2/SHDSL span."::={ hdsl2ShdslSpanStatusEntry 4}-- Unit Inventory Group
--hdsl2ShdslInventoryTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslInventoryEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports retrieval of unit inventory information
available via the EOC from units in a HDSL2/SHDSL line.
Entries in this table are dynamically created during the
line discovery process. The life cycle for these entries
is as follows:
- xtu discovers a device, either a far-end xtu or an xru
- an inventory table entry is created for the device
- the line goes down for whatever reason
- inventory table entries for unreachable devices are
destroyed.
As these entries are created/destroyed dynamically, they
are NOT persistent."::={ hdsl2ShdslMibObjects 3}hdsl2ShdslInventoryEntry OBJECT-TYPESYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit."INDEX{ ifIndex, hdsl2ShdslInvIndex }::={ hdsl2ShdslInventoryTable 1}
Hdsl2ShdslInventoryEntry ::=SEQUENCE{
hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTETSTRING,
hdsl2ShdslInvVendorModelNumber OCTETSTRING,
hdsl2ShdslInvVendorSerialNumber OCTETSTRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTETSTRING,
hdsl2ShdslInvVendorIssueNumber OCTETSTRING,
hdsl2ShdslInvVendorSoftwareVersion OCTETSTRING,
hdsl2ShdslInvEquipmentCode OCTETSTRING,
hdsl2ShdslInvVendorOther OCTETSTRING,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType}hdsl2ShdslInvIndex OBJECT-TYPESYNTAXHdsl2ShdslUnitIdMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry in this table corresponds to a physical element
in a HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."::={ hdsl2ShdslInventoryEntry 1}hdsl2ShdslInvVendorID OBJECT-TYPESYNTAXOCTETSTRING(SIZE(8))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vendor ID as reported in an Inventory Response message."::={ hdsl2ShdslInventoryEntry 2}hdsl2ShdslInvVendorModelNumber OBJECT-TYPESYNTAXOCTETSTRING(SIZE(12))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vendor model number as reported in an Inventory Response
message."::={ hdsl2ShdslInventoryEntry 3}
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPESYNTAXOCTETSTRING(SIZE(12))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vendor serial number as reported in an Inventory Response
message."::={ hdsl2ShdslInventoryEntry 4}hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vendor EOC version as reported in a Discovery Response
message."::={ hdsl2ShdslInventoryEntry 5}hdsl2ShdslInvStandardVersion OBJECT-TYPESYNTAXInteger32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."::={ hdsl2ShdslInventoryEntry 6}
hdsl2ShdslInvVendorListNumber OBJECT-TYPESYNTAXOCTETSTRING(SIZE(3))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vendor list number as reported in an Inventory Response
message."::={ hdsl2ShdslInventoryEntry 7}hdsl2ShdslInvVendorIssueNumber OBJECT-TYPESYNTAXOCTETSTRING(SIZE(2))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Vendor issue number as reported in an Inventory Response
message."::={ hdsl2ShdslInventoryEntry 8}hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPESYNTAXOCTETSTRING(SIZE(6))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Vendor software version as reported in an Inventory Response
message."::={ hdsl2ShdslInventoryEntry 9}hdsl2ShdslInvEquipmentCode OBJECT-TYPESYNTAXOCTETSTRING(SIZE(10))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."::={ hdsl2ShdslInventoryEntry 10}hdsl2ShdslInvVendorOther OBJECT-TYPESYNTAXOCTETSTRING(SIZE(12))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Other vendor information as reported in an Inventory Response
message."::={ hdsl2ShdslInventoryEntry 11}hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPESYNTAXHdsl2ShdslTransmissionModeTypeMAX-ACCESSread-only
STATUScurrentDESCRIPTION"Contains the transmission mode capability of the SHDSL unit."::={ hdsl2ShdslInventoryEntry 12}-- Segment Endpoint Configuration Group
--hdsl2ShdslEndpointConfTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslEndpointConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."::={ hdsl2ShdslMibObjects 4}hdsl2ShdslEndpointConfEntry OBJECT-TYPESYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the
wire-pair of the associated modem."INDEX{ ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair}::={ hdsl2ShdslEndpointConfTable 1}
Hdsl2ShdslEndpointConfEntry ::=SEQUENCE{
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString}hdsl2ShdslEndpointSide OBJECT-TYPESYNTAXHdsl2ShdslUnitSideMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide textual
convention."::={ hdsl2ShdslEndpointConfEntry 1}hdsl2ShdslEndpointWirePair OBJECT-TYPESYNTAXHdsl2ShdslWirePairMAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The wire-pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention."::={ hdsl2ShdslEndpointConfEntry 2}hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPESYNTAXSnmpAdminString(SIZE(0..32))MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object configures the alarm threshold values to be used
for this segment endpoint. The values are obtained from the
alarm configuration profile referenced by this object. The
value of this object is the index of the referenced profile in
the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero-
length SnmpAdminString). If the value is a zero-length
SnmpAdminString, the endpoint uses the default Alarm
Configuration Profile for the associated span as per the
hdsl2ShdslSpanConfAlarmProfile object in the
hdsl2ShdslSpanConfTable. The default value of this object is
a zero-length SnmpAdminString.
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."::={ hdsl2ShdslEndpointConfEntry 3}-- Segment Endpoint Current Status/Performance Group
--hdsl2ShdslEndpointCurrTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner."::={ hdsl2ShdslMibObjects 5}hdsl2ShdslEndpointCurrEntry OBJECT-TYPESYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire-pair of the associated modem."INDEX{ ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair }::={ hdsl2ShdslEndpointCurrTable 1}
Hdsl2ShdslEndpointCurrEntry ::=SEQUENCE{
hdsl2ShdslEndpointCurrAtn Integer32,
hdsl2ShdslEndpointCurrSnrMgn Integer32,
hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DayES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DaySES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayCRCanomalies
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayLOSWS
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayUAS
Hdsl2ShdslPerfCurrDayCount
}hdsl2ShdslEndpointCurrAtn OBJECT-TYPESYNTAXInteger32(-127..128)UNITS"dB"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 1}hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPESYNTAXInteger32(-127..128)UNITS"dB"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 2}hdsl2ShdslEndpointCurrStatus OBJECT-TYPESYNTAXBITS
{noDefect(0),powerBackoff(1),deviceFault(2),dcContinuityFault(3),snrMarginAlarm(4),loopAttenuationAlarm(5),loswFailureAlarm(6),configInitFailure(7),protocolInitFailure(8),noNeighborPresent(9),loopbackActive(10)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Contains the current state of the endpoint. This is a
bitmap of possible conditions. The various bit positions
are:
noDefect There no defects on the line.
powerBackoff Indicates enhanced Power Backoff.
deviceFault Indicates a vendor-dependent
diagnostic or self-test fault
has been detected.
dcContinuityFault Indicates vendor-dependent
conditions that interfere with
span powering such as short and
open circuits.
snrMarginAlarm Indicates that the SNR margin
has dropped below the alarm threshold.
loopAttenuationAlarm Indicates that the loop attenuation
exceeds the alarm threshold.
loswFailureAlarm Indicates a forward LOSW alarm.
configInitFailure Endpoint failure during initialization
due to paired endpoint not able to
support requested configuration.
protocolInitFailure Endpoint failure during initialization
due to incompatible protocol used by
the paired endpoint.
noNeighborPresent Endpoint failure during initialization
due to no activation sequence detected
from paired endpoint.
loopbackActive A loopback is currently active at this
Segment Endpoint.
This is intended to supplement ifOperStatus. Note that there
is a 1-1 relationship between the status bits defined in this
object and the notification thresholds defined elsewhere in
this MIB."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 3}hdsl2ShdslEndpointES OBJECT-TYPESYNTAXCounter32UNITS"seconds"
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 4}hdsl2ShdslEndpointSES OBJECT-TYPESYNTAXCounter32UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 5}hdsl2ShdslEndpointCRCanomalies OBJECT-TYPESYNTAXCounter32UNITS"detected CRC Anomalies"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of CRC anomalies on this endpoint since the xU was
last restarted."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::={ hdsl2ShdslEndpointCurrEntry 6}hdsl2ShdslEndpointLOSWS OBJECT-TYPESYNTAXCounter32UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 7}hdsl2ShdslEndpointUAS OBJECT-TYPESYNTAXCounter32UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 8}hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPESYNTAXHdsl2ShdslPerfTimeElapsedUNITS"seconds"MAX-ACCESSread-only
STATUScurrentDESCRIPTION"Total elapsed seconds in the current 15-minute interval."::={ hdsl2ShdslEndpointCurrEntry 9}hdsl2ShdslEndpointCurr15MinES OBJECT-TYPESYNTAXPerfCurrentCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Errored Seconds (ES) in the current 15-minute
interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 10}hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPESYNTAXPerfCurrentCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Severely Errored Seconds (SES) in the current
15-minute interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 11}hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
SYNTAXPerfCurrentCountUNITS"detected CRC Anomalies"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of CRC anomalies in the current 15-minute interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 12}hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPESYNTAXPerfCurrentCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 13}hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPESYNTAXPerfCurrentCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 14}hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPESYNTAXHdsl2ShdslPerfTimeElapsedUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Number of seconds that have elapsed since the beginning of
the current 1-day interval."::={ hdsl2ShdslEndpointCurrEntry 15}hdsl2ShdslEndpointCurr1DayES OBJECT-TYPESYNTAXHdsl2ShdslPerfCurrDayCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 16}hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPESYNTAXHdsl2ShdslPerfCurrDayCount
UNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 17}hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPESYNTAXHdsl2ShdslPerfCurrDayCountUNITS"detected CRC Anomalies"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 18}hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPESYNTAXHdsl2ShdslPerfCurrDayCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 19}hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPESYNTAXHdsl2ShdslPerfCurrDayCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2ShdslEndpointCurrEntry 20}-- Segment Endpoint 15-Minute Interval Status/Performance Group
--hdsl2Shdsl15MinIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."::={ hdsl2ShdslMibObjects 6}
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPESYNTAX Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the hdsl2Shdsl15MinIntervalTable."INDEX{ ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}::={ hdsl2Shdsl15MinIntervalTable 1}
Hdsl2Shdsl15MinIntervalEntry ::=SEQUENCE{
hdsl2Shdsl15MinIntervalNumber Unsigned32,
hdsl2Shdsl15MinIntervalES PerfIntervalCount,
hdsl2Shdsl15MinIntervalSES PerfIntervalCount,
hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount,
hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount,
hdsl2Shdsl15MinIntervalUAS PerfIntervalCount}hdsl2Shdsl15MinIntervalNumber OBJECT-TYPESYNTAXUnsigned32(1..96)
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Performance Data Interval number. 1 is the the most recent
previous interval; interval 96 is 24 hours ago. Intervals
2..96 are optional."::={ hdsl2Shdsl15MinIntervalEntry 1}hdsl2Shdsl15MinIntervalES OBJECT-TYPESYNTAXPerfIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Errored Seconds (ES) during the interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl15MinIntervalEntry 2}hdsl2Shdsl15MinIntervalSES OBJECT-TYPESYNTAXPerfIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Severely Errored Seconds (SES) during the interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl15MinIntervalEntry 3}
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPESYNTAXPerfIntervalCountUNITS"detected CRC Anomalies"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of CRC anomalies during the interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl15MinIntervalEntry 4}hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPESYNTAXPerfIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Loss of Sync Word (LOSW) Seconds during the
interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl15MinIntervalEntry 5}hdsl2Shdsl15MinIntervalUAS OBJECT-TYPESYNTAXPerfIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl15MinIntervalEntry 6}-- Segment Endpoint 1-Day Interval Status/Performance Group
--hdsl2Shdsl1DayIntervalTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."::={ hdsl2ShdslMibObjects 7}hdsl2Shdsl1DayIntervalEntry OBJECT-TYPESYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the hdsl2Shdsl1DayIntervalTable."INDEX{ ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }::={ hdsl2Shdsl1DayIntervalTable 1}
Hdsl2Shdsl1DayIntervalEntry ::=SEQUENCE{
hdsl2Shdsl1DayIntervalNumber Unsigned32,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount}hdsl2Shdsl1DayIntervalNumber OBJECT-TYPESYNTAXUnsigned32(1..30)MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"History Data Interval number. Interval 1 is the the most
recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional."::={ hdsl2Shdsl1DayIntervalEntry 1}hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPESYNTAXHdsl2ShdslPerfTimeElapsedUNITS"seconds"
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."::={ hdsl2Shdsl1DayIntervalEntry 2}hdsl2Shdsl1DayIntervalES OBJECT-TYPESYNTAXHdsl2Shdsl1DayIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Errored Seconds (ES) during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl1DayIntervalEntry 3}hdsl2Shdsl1DayIntervalSES OBJECT-TYPESYNTAXHdsl2Shdsl1DayIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl1DayIntervalEntry 4}hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPESYNTAXHdsl2Shdsl1DayIntervalCountUNITS"detected CRC Anomalies"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl1DayIntervalEntry 5}hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPESYNTAXHdsl2Shdsl1DayIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl1DayIntervalEntry 6}
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPESYNTAXHdsl2Shdsl1DayIntervalCountUNITS"seconds"MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs."REFERENCE"HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"::={ hdsl2Shdsl1DayIntervalEntry 7}-- Maintenance Group
--hdsl2ShdslEndpointMaintTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslEndpointMaintEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints. This table
contains live data from equipment. As such, it is NOT
persistent."::={ hdsl2ShdslMibObjects 8}hdsl2ShdslEndpointMaintEntry OBJECT-TYPESYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit."INDEX{ ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }::={ hdsl2ShdslEndpointMaintTable 1}
Hdsl2ShdslEndpointMaintEntry ::=SEQUENCE{
hdsl2ShdslMaintLoopbackConfig INTEGER,
hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER}hdsl2ShdslMaintLoopbackConfig OBJECT-TYPESYNTAXINTEGER{noLoopback(1),normalLoopback(2),specialLoopback(3)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object."::={ hdsl2ShdslEndpointMaintEntry 1}hdsl2ShdslMaintTipRingReversal OBJECT-TYPESYNTAXINTEGER{normal(1),reversed(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the state of the tip/ring pair at the
associated segment endpoint."::={ hdsl2ShdslEndpointMaintEntry 2}hdsl2ShdslMaintPowerBackOff OBJECT-TYPESYNTAXINTEGER{default(1),enhanced(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode."::={ hdsl2ShdslEndpointMaintEntry 3}hdsl2ShdslMaintSoftRestart OBJECT-TYPESYNTAXINTEGER{ready(1),restart(2)}MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The manager
may only set this object to the 'restart(2)' value, which
initiates a restart. The agent will perform a restart after
approximately 5 seconds. Following the 5 second period, the
agent will restore the object to the 'ready(1)' state."::={ hdsl2ShdslEndpointMaintEntry 4}hdsl2ShdslUnitMaintTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslUnitMaintEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports maintenance operations for units in a
HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."::={ hdsl2ShdslMibObjects 9}
hdsl2ShdslUnitMaintEntry OBJECT-TYPESYNTAX Hdsl2ShdslUnitMaintEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit, and is indexed by the ifIndex
of the HDSL2/SHDSL line and the UnitId of the associated
unit."INDEX{ ifIndex, hdsl2ShdslInvIndex }::={ hdsl2ShdslUnitMaintTable 1}
Hdsl2ShdslUnitMaintEntry ::=SEQUENCE{
hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER}hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPESYNTAXInteger32(0..4095)UNITS"minutes"MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout."
::={ hdsl2ShdslUnitMaintEntry 1}hdsl2ShdslMaintUnitPowerSource OBJECT-TYPESYNTAXINTEGER{local(1),span(2)}MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the DC power source being used by the
associated unit."::={ hdsl2ShdslUnitMaintEntry 2}-- Span Configuration Profile Group
--hdsl2ShdslSpanConfProfileTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner."::={ hdsl2ShdslMibObjects 10}hdsl2ShdslSpanConfProfileEntry OBJECT-TYPESYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."INDEX{IMPLIED hdsl2ShdslSpanConfProfileName }::={ hdsl2ShdslSpanConfProfileTable 1}
Hdsl2ShdslSpanConfProfileEntry ::=SEQUENCE{
hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Unsigned32,
hdsl2ShdslSpanConfMaxLineRate Unsigned32,
hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32,
hdsl2ShdslSpanConfUsedTargetMargins BITS,
hdsl2ShdslSpanConfReferenceClock
Hdsl2ShdslClockReferenceType,
hdsl2ShdslSpanConfLineProbeEnable INTEGER,
hdsl2ShdslSpanConfProfileRowStatus RowStatus}hdsl2ShdslSpanConfProfileName OBJECT-TYPESYNTAXSnmpAdminString(SIZE(1..32))MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."::={ hdsl2ShdslSpanConfProfileEntry 1}hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAXINTEGER{twoWire(1),fourWire(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the two-wire or optional four-wire
operation for SHDSL Lines."DEFVAL{ twoWire }::={ hdsl2ShdslSpanConfProfileEntry 2}hdsl2ShdslSpanConfMinLineRate OBJECT-TYPESYNTAXUnsigned32(0..4112000)UNITS"bps"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."DEFVAL{1552000}
::={ hdsl2ShdslSpanConfProfileEntry 3}hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPESYNTAXUnsigned32(0..4112000)UNITS"bps"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."DEFVAL{1552000}::={ hdsl2ShdslSpanConfProfileEntry 4}hdsl2ShdslSpanConfPSD OBJECT-TYPESYNTAXINTEGER{symmetric(1),asymmetric(2)}MAX-ACCESSread-createSTATUScurrent
DESCRIPTION"This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional."DEFVAL{ symmetric }::={ hdsl2ShdslSpanConfProfileEntry 5}hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPESYNTAXHdsl2ShdslTransmissionModeTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the regional setting for the SHDSL
line."DEFVAL{{ region1 }}::={ hdsl2ShdslSpanConfProfileEntry 6}hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPESYNTAXINTEGER{enabled(1),disabled(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION
"This object enables/disables support for remote management
of the units in a SHDSL line from the STU-R via the EOC."DEFVAL{ enabled }::={ hdsl2ShdslSpanConfProfileEntry 7}hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPESYNTAXINTEGER{noPower(1),powerFeed(2),wettingCurrent(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object enables/disables support for optional power
feeding in a SHDSL line."DEFVAL{ noPower }::={ hdsl2ShdslSpanConfProfileEntry 8}hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPESYNTAXInteger32(-10..21)UNITS"dB"MAX-ACCESSread-create
STATUScurrentDESCRIPTION"This object specifies the downstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."DEFVAL{0}::={ hdsl2ShdslSpanConfProfileEntry 9}hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPESYNTAXInteger32(-10..21)UNITS"dB"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."DEFVAL{0}::={ hdsl2ShdslSpanConfProfileEntry 10}hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPESYNTAXInteger32(-10..21)
UNITS"dB"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the upstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."DEFVAL{0}::={ hdsl2ShdslSpanConfProfileEntry 11}hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPESYNTAXInteger32(-10..21)UNITS"dB"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."DEFVAL{0}::={ hdsl2ShdslSpanConfProfileEntry 12}hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAXBITS{currCondDown(0),worstCaseDown(1),currCondUp(2),worstCaseUp(3)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"Contains indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The
various bit positions are:
currCondDown current condition downstream target SNR
margin enabled
worstCaseDown worst case downstream target SNR margin
enabled
currCondUp current condition upstream target SNR
margin enabled
worstCaseUp worst case upstream target SNR margin
enabled."DEFVAL{{ currCondDown }}::={ hdsl2ShdslSpanConfProfileEntry 13}hdsl2ShdslSpanConfReferenceClock OBJECT-TYPESYNTAXHdsl2ShdslClockReferenceTypeMAX-ACCESSread-createSTATUScurrent
DESCRIPTION"This object configures the clock reference for the STU-C
in a SHDSL Line."DEFVAL{ localClk }::={ hdsl2ShdslSpanConfProfileEntry 14}hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPESYNTAXINTEGER{disable(1),enable(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. If Line probe is disabled, the rate adaptation phase
is skipped to shorten set up time."DEFVAL{ disable }::={ hdsl2ShdslSpanConfProfileEntry 15}hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrent
DESCRIPTION"This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."::={ hdsl2ShdslSpanConfProfileEntry 16}-- Segment Endpoint Alarm Configuration Profile group
--hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPESYNTAXSEQUENCEOF Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."::={ hdsl2ShdslMibObjects 11}hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPESYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."INDEX{IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }::={ hdsl2ShdslEndpointAlarmConfProfileTable 1}
Hdsl2ShdslEndpointAlarmConfProfileEntry ::=SEQUENCE{
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus}hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPESYNTAXSnmpAdminString(SIZE(1..32))
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object is the unique index associated with this profile."::={ hdsl2ShdslEndpointAlarmConfProfileEntry 1}hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPESYNTAXInteger32(-127..128)UNITS"dB"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing
MAY be generated."DEFVAL{0}::={ hdsl2ShdslEndpointAlarmConfProfileEntry 2}hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPESYNTAXInteger32(-127..128)UNITS"dB"
MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the SNR margin alarm threshold.
When the current value of hdsl2ShdslEndpointCurrSnrMgn
reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."DEFVAL{0}::={ hdsl2ShdslEndpointAlarmConfProfileEntry 3}hdsl2ShdslEndpointThreshES OBJECT-TYPESYNTAXHdsl2ShdslPerfIntervalThresholdUNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the threshold for the number of
errored seconds (ES) within any given 15-minute performance
data collection interval. If the value of errored seconds
in a particular 15-minute collection interval reaches/
exceeds this value, a hdsl2ShdslPerfESThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."DEFVAL{0}::={ hdsl2ShdslEndpointAlarmConfProfileEntry 4}hdsl2ShdslEndpointThreshSES OBJECT-TYPESYNTAXHdsl2ShdslPerfIntervalThreshold
UNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the threshold for the number of
severely errored seconds (SES) within any given 15-minute
performance data collection interval. If the value of
severely errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh
MAY be generated. At most one notification will be sent per
interval per endpoint."DEFVAL{0}::={ hdsl2ShdslEndpointAlarmConfProfileEntry 5}hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPESYNTAXInteger32UNITS"detected CRC Anomalies"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."DEFVAL{0}
::={ hdsl2ShdslEndpointAlarmConfProfileEntry 6}hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPESYNTAXHdsl2ShdslPerfIntervalThresholdUNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."DEFVAL{0}::={ hdsl2ShdslEndpointAlarmConfProfileEntry 7}hdsl2ShdslEndpointThreshUAS OBJECT-TYPESYNTAXHdsl2ShdslPerfIntervalThresholdUNITS"seconds"MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object configures the threshold for the number of
unavailable seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfUASThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."DEFVAL{0}::={ hdsl2ShdslEndpointAlarmConfProfileEntry 8}hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."::={ hdsl2ShdslEndpointAlarmConfProfileEntry 9}-- Notifications Group
--hdsl2ShdslNotifications OBJECTIDENTIFIER::={ hdsl2ShdslMIB 0}hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation
}STATUScurrentDESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."::={ hdsl2ShdslNotifications 1}hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin
}STATUScurrentDESCRIPTION"This notification indicates that the SNR margin threshold (as
per the hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."::={ hdsl2ShdslNotifications 2}hdsl2ShdslPerfESThresh NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
}STATUScurrentDESCRIPTION"This notification indicates that the errored seconds threshold
(as per the hdsl2ShdslEndpointThreshES value) has been reached/
exceeded for the HDSL2/SHDSL segment endpoint."::={ hdsl2ShdslNotifications 3}hdsl2ShdslPerfSESThresh NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES
}STATUScurrentDESCRIPTION"This notification indicates that the severely errored seconds
threshold (as per the hdsl2ShdslEndpointThreshSES value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."::={ hdsl2ShdslNotifications 4}hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies
}STATUScurrentDESCRIPTION"This notification indicates that the CRC anomalies threshold
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."::={ hdsl2ShdslNotifications 5}hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS
}STATUScurrentDESCRIPTION"This notification indicates that the LOSW seconds threshold
(as per the hdsl2ShdslEndpointThreshLOSWS value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::={ hdsl2ShdslNotifications 6}hdsl2ShdslPerfUASThresh NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS
}STATUScurrentDESCRIPTION"This notification indicates that the unavailable seconds
threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."::={ hdsl2ShdslNotifications 7}hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslSpanConfNumRepeaters
}STATUScurrentDESCRIPTION"This notification indicates that a mismatch has been detected
between the number of repeater/regenerator units configured
for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of repeater/regenerator units
discovered via the EOC."::={ hdsl2ShdslNotifications 8}hdsl2ShdslLoopbackFailure NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslMaintLoopbackConfig
}STATUScurrentDESCRIPTION
"This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment."::={ hdsl2ShdslNotifications 9}hdsl2ShdslpowerBackoff NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrStatus
}STATUScurrentDESCRIPTION"This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."::={ hdsl2ShdslNotifications 10}hdsl2ShdsldeviceFault NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrStatus
}STATUScurrentDESCRIPTION"This notification indicates that the bit setting for
deviceFault in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."::={ hdsl2ShdslNotifications 11}hdsl2ShdsldcContinuityFault NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrStatus
}STATUScurrentDESCRIPTION"This notification indicates that the bit setting for
dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."::={ hdsl2ShdslNotifications 12}hdsl2ShdslconfigInitFailure NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrStatus
}STATUScurrentDESCRIPTION"This notification indicates that the bit setting for
configInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."::={ hdsl2ShdslNotifications 13}hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrStatus
}STATUScurrentDESCRIPTION"This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
object for this endpoint has changed."::={ hdsl2ShdslNotifications 14}hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslEndpointCurrStatus
}STATUScurrentDESCRIPTION"This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."::={ hdsl2ShdslNotifications 15}hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPEOBJECTS{
hdsl2ShdslInvVendorID
}STATUScurrentDESCRIPTION"This notification indicates impending unit failure due to
loss of local power (last gasp)."::={ hdsl2ShdslNotifications 16}-- conformance information
--hdsl2ShdslConformance OBJECTIDENTIFIER::={ hdsl2ShdslMIB 3}hdsl2ShdslGroups OBJECTIDENTIFIER::={ hdsl2ShdslConformance 1}hdsl2ShdslCompliances OBJECTIDENTIFIER::={ hdsl2ShdslConformance 2}-- agent compliance statementshdsl2ShdslLineMibCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The section outlines compliance requirements for this MIB."MODULEMANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}GROUP hdsl2ShdslInventoryShdslGroup
DESCRIPTION"Support for this group is only required for implementations
supporting SHDSL lines."GROUP hdsl2ShdslSpanShdslStatusGroup
DESCRIPTION"Support for this group is only required for implementations
supporting SHDSL lines."GROUP hdsl2ShdslSpanConfProfileGroup
DESCRIPTION"Support for this group is only required for implementations
supporting SHDSL lines."::={ hdsl2ShdslCompliances 1}-- units of conformance
--hdsl2ShdslSpanConfGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslSpanConfNumRepeaters,
hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanConfAlarmProfile
}STATUScurrentDESCRIPTION"This group supports objects for configuring span related
parameters for HDSL2/SHDSL lines."::={ hdsl2ShdslGroups 1}hdsl2ShdslSpanStatusGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslStatusNumAvailRepeaters
}STATUScurrentDESCRIPTION"This group supports objects for retrieving span related
status for HDSL2/SHDSL lines."::={ hdsl2ShdslGroups 2}hdsl2ShdslInventoryShdslGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslInvTransmissionModeCapability
}STATUScurrentDESCRIPTION"This group supports objects for retrieving SHDSL-specific
inventory information."::={ hdsl2ShdslGroups 3}hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}STATUScurrentDESCRIPTION"This group supports objects for retrieving SHDSL-specific
span related status."::={ hdsl2ShdslGroups 4}
hdsl2ShdslInventoryGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther
}STATUScurrentDESCRIPTION"This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines."::={ hdsl2ShdslGroups 5}hdsl2ShdslEndpointConfGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslEndpointCurrAtn
}STATUScurrentDESCRIPTION"This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines."::={ hdsl2ShdslGroups 6}hdsl2ShdslEndpointCurrGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus,
hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES,
hdsl2ShdslEndpointCRCanomalies,
hdsl2ShdslEndpointLOSWS,
hdsl2ShdslEndpointUAS,
hdsl2ShdslEndpointCurr15MinTimeElapsed,
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointCurr1DayTimeElapsed,
hdsl2ShdslEndpointCurr1DayES,
hdsl2ShdslEndpointCurr1DaySES,
hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS
}STATUScurrentDESCRIPTION"This group supports objects which provide current status and
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines."::={ hdsl2ShdslGroups 7}hdsl2Shdsl15MinIntervalGroup OBJECT-GROUPOBJECTS{
hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies,
hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS
}
STATUScurrentDESCRIPTION"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 15-minute intervals."::={ hdsl2ShdslGroups 8}hdsl2Shdsl1DayIntervalGroup OBJECT-GROUPOBJECTS{
hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS
}STATUScurrentDESCRIPTION"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 1-day intervals."::={ hdsl2ShdslGroups 9}hdsl2ShdslMaintenanceGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslMaintLoopbackConfig,
hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource
}STATUScurrentDESCRIPTION
"This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines."::={ hdsl2ShdslGroups 10}hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslEndpointAlarmConfProfile,
hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS,
hdsl2ShdslEndpointAlarmConfProfileRowStatus
}STATUScurrentDESCRIPTION"This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL
lines."::={ hdsl2ShdslGroups 11}hdsl2ShdslNotificationGroup NOTIFICATION-GROUPNOTIFICATIONS{
hdsl2ShdslLoopAttenCrossing,
hdsl2ShdslSNRMarginCrossing,
hdsl2ShdslPerfESThresh,
hdsl2ShdslPerfSESThresh,
hdsl2ShdslPerfCRCanomaliesThresh,
hdsl2ShdslPerfLOSWSThresh,
hdsl2ShdslPerfUASThresh,
hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure,
hdsl2ShdslpowerBackoff,
hdsl2ShdsldeviceFault,
hdsl2ShdsldcContinuityFault,
hdsl2ShdslconfigInitFailure,
hdsl2ShdslprotocolInitFailure,
hdsl2ShdslnoNeighborPresent,
hdsl2ShdslLocalPowerLoss
}STATUScurrentDESCRIPTION"This group supports notifications of significant conditions
associated with HDSL2/SHDSL lines."::={ hdsl2ShdslGroups 12}hdsl2ShdslSpanConfProfileGroup OBJECT-GROUPOBJECTS{
hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfReferenceClock,
hdsl2ShdslSpanConfLineProbeEnable,
hdsl2ShdslSpanConfProfileRowStatus
}STATUScurrent
DESCRIPTION"This group supports objects that constitute configuration
profiles for configuring span related parameters in SHDSL
lines."::={ hdsl2ShdslGroups 13}END